PVP no incluye IVA
InteliSys NTC BaseBox – ComAp
Premium Gen-set Controller
Marine certified controller.
Manufacturer | ComAp |
PVP no incluye IVA
ComAp InteliCharger 65 12-A Automatic Battery Charger
- 12V advanced automatic battery charger
- 6A current output
- Robust & high reliability
Manufacturer | ComAp |
PVP no incluye IVA
- 12V advanced automatic battery charger
- 6A current output
- High efficiency
- Compact size
- Sealed electronic construction
- Robust & high reliability
Manufacturer | ComAp |
PVP no incluye IVA
ComAp InteliCharger 120 12 Automatic Battery Charger
The InteliCharger 120 12 is an advanced, automatic, multi-stage battery charger using “Switched mode technology” and “Battery care philosophy”, suited to meet the most advanced requirements of battery manufacturers.
Features:
- 12 V / 10 A nominal output
- Adjustable voltage and current output
- High efficiency ≥ 89 %
- Universal AC input range
- Automatic battery status diagnosis
- Microprocessor controlled charging algorithm
Manufacturer | ComAp |
PVP no incluye IVA
ComAp InteliCharger 120 12-24 | Automatic Battery Charger ICHG-120 12-24
The InteliCharger 120 12-24 is an advanced, automatic, multi-stage battery charger using “Switched mode technology” and “Battery care philosophy”, suited to meet the most advanced requirements of battery manufacturers.
Features:
- 24 V / 5 A or 12 V / 6 A output
- Adjustable voltage and current output
- High efficiency ≥ 90 %
- Universal AC input range
- Automatic battery status diagnosis
- Microprocessor controlled charging algorithm
Manufacturer | ComAp |
PVP no incluye IVA
InteliCharger 60 24-AF ComAp | Automatic Battery Charger | ICHG-60-24-AF
- 24V advanced automatic battery charger
- 3A current output
- High efficiency
- Cost effective
- Compact size
- Sealed electronic construction
- Robust & high reliability
- Fully automatic operation
Manufacturer | ComAp |
PVP no incluye IVA
The InteliATSNT controllers are designed to monitor the incoming AC mains
supply (1 or 3 phases) for under voltage, over voltage, under frequency, over
frequency and voltage unbalance. In the case of any mains supply disproportion
it will send a remote start command to the generating set and make change
over for both generator and mains contactors.
The gen-set requires a remote start type control unit (e.g. the ComAp InteliLiteNT MRS 10 controller).
Manufacturer | ComAp |
PVP no incluye IVA
Internet connection for one or more ComAp controllers, either by Ethernet cable or by built in 3.75G Cellular modem
Wireless high speed GPRS/UMTS modem built in
Supports all cellular packet data systems from GPRS to HSPA (2.5G to 3.75G)
Full Multiband support – modem works globally
Ethernet wired connection for local LAN connection
Single module can be used for multiple controllers on the same site (connected via CAN or RS485)
MODBUS/TCP, SNMP protocol support – direct connection to building management and other systems
Includes ComAp AirGate technology – easy plug-and-play connection anywhere (no fixed IP needed)
Designed for WebSupervisor – fully supported by ComAp’s cloud-based remote monitoring system
Global positioning system built in* – keep track of your equipment
Durable metal housing with DIN rail mount
SIM card holder access without disassembly
SMA connectors for external GPS and GSM antenna
Wide range 8–36 VDC supply voltage
Works with ComAp monitoring software in either direct connection or via AirGate technology
Manufacturer | Comap |
In stock
PVP no incluye IVA
SPECIFICATION
DC SUPPLY
CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
CRANKING DROPOUTSAble to survive 0 V for 50 mS, providing
supply was at least 10 V before dropout and
supply recovers to 5 V. This is achieved
without the need for internal batteries.
LEDs and backlight will not be maintained
during cranking.MAXIMUM OPERATING CURRENT
168 mA at 12 V, 80 mA at 24 V
MAXIMUM STANDBY CURRENT
39 mA at 12 V, 20 mA at 24 V
OUTPUTS
OUTPUT A & BNormally open volt-free output
8 A DC at 35 V DCOUTPUT C & D
Changeover volt-free output
8 A DC at 35 V DCAUXILLARY OUTPUT E, F, G & H
2 A DC at supply voltage
S1 & S2
VOLTAGE RANGE
15 V to 333 V AC (L-N)
FREQUENCY RANGE
3.5 Hz to 75 Hz
DIMENSIONS
OVERALL180 mm x 116 mm x 42 mm
7.1” x 4.6” x 1.7”PANEL CUT-OUT
154 mm x 98 mm
6” x 3.9”MAXIMUM PANEL THICKNESS
8 mm
0.3”
OPERATING TEMPERATURE RANGE
-30°C to +70°C
STORAGE TEMPERATURE RANGE
-40°C to +80°C
Manufacturer | Deep Sea Electronics |
PVP no incluye IVA
The DSE6110 MKIII is an Auto Start Control Module suitable for a wide variety of single, diesel or gas, genset applications.
Monitoring an extensive number of engine parameters, the module will display warnings, shutdown and engine status information on the back-lit LCD screen, illuminated LEDs and remote PC.
The module includes USB connection and dedicated DSENet® terminals for system expansion.
The module is compatible with electronic (CAN) and non-electronic (magnetic pick-up/alternator sensing) engines and offers an extensive number of flexible inputs, outputs and extensive engine protections so the system can be easily adapted to meet the most demanding industry requirements.
Manufacturer | Deep Sea Electronics |
The controllers are automatic control systems for the handling of generating sets. They consist of a device containing indispensable software for manoeuvring and calibrating power generating machines. Thanks to the control units it is possible to monitor all parameters, monitor and calibrate the levels of the generating sets.
They are high-tech controllers that allow the supervision, both manually and automatically, of the starting, stopping and protection systems of the main systems that make up the energy supply machines. The central units for generators are suitable for emergency installations (mains voltage failure) or for autonomous generating sets (voltage-free contact starting).
Depending on the type of controller a generator set requires, it may offer more or less functionality. However, they all offer a manufacturer's guarantee in accordance with international standards.
The controllers are able to offer a very fast response to control the different parameters to be analyzed. They usually have a screen to show any change, alarm or sound defect. In the product cards are detailed the characteristics of each model of controller for generating sets.