InteliLite NT MRS 3 – ComAp

Manual Remote Start (MRS) Gen-set Controller

• Compact gen-set controller for single operating genset
• Manual and remote start (MRS) applications
• Easy to setup
• Wide gen-set monitoring and protection
• Running hours event and performance log
• Multiple languages (user changeable) in controller, even more in installation suite
• Plug-in extension modules capability
• Automatic SMS on alarm or event & gen-set control over SMS (* Plug-in module required)
• Modbus
• Automatic GCB control
• D+ preexcitation terminal
• True RMS measurement
• 3 phase power measurement
• 3 configurable analog inputs
• 4 binary inputs
• 4 binary outputs

InteliLite NT MRS 4 – ComAp

Manual Remote Start (MRS) Gen-set Controller

·        Compact gen-set controller for single operating genset

·        Manual and remote start (MRS) applications

·        Easy to setup

·        Wide gen-set monitoring and protection

·        Outstanding EFI engine support with diagnostic messages in plain text via J1939

·        Running hours event and performance log

·        Multiple languages (user changeable) in controller, even more in installation suite

·        Plug-in extension modules capability

·        Automatic SMS on alarm or event & gen-set control over SMS (*Plug-in module required)

·        Modbus

·        Automatic GCB control

·        D+ preexcitation terminal

·        True RMS measurement

·        3 phase power measurement

·        3 configurable analog inputs

·        4 binary inputs

·        4 binary outputs

InteliLite NT AMF 8 – ComAp

Auto Mains Failure (AMF) Gen-set Controller

• Compact gen-set controller for single genset operating in standby prime power modes
• Meets all requirements for Auto Mains Failure (AMF) applications
• Easy to setup
• Wide gen-set monitoring and protection
• Running hours event and performance log
• Multiple languages (user changeable) in controller, even more in installation suite
• Plug-in extension modules capability

·        Automatic SMS on alarm or event & gen-set control over SMS (*Plug-in module required)

• Modbus
• Supports prime power (MRS) applications
• Automatic and manual GCB and MCB control
• D+ preexcitation terminal
• True RMS measurement
• 3 phase power measurement
• 3 configurable analog inputs
• 4 binary inputs
• 6 binary outputs 

InteliLite 9 - ComAp (IL3LAMF9BAA)

Auto Mains Failure (AMF) Gen-set Controller

• Compact gen-set controller for single genset operating in standby and prime power modes
• Easy to setup
• Wide gen-set monitoring and protection
• Outstanding EFI engine support with diagnostic messages in plain text via J1939
• Running hours event and performance log
• Multiple languages (user changeable) in controller, even more in installation suite
• Plug-in extension modules capability

·        Automatic SMS on alarm or event & gen-set control over SMS (*Plug-in module required)

• Modbus
• Supports prime power (MRS) applications
• Automatic and manual GCB and MCB control
• D+ preexcitation terminal
• True RMS measurement
• 3 phase power measurement
• 3 configurable analog inputs
• 4 binary inputs
• 6 binary outputs

InteliLite MRS 11 - ComAp

Next generation of Manual & Remote Start (MRS) gen-set controller

New generation of one of the world's most successful controllers in its class.

Single gen-set controller for prime power applications.

• Single gen-set controller for prime power applications
• Easy to install, configure and use
• 5 languages in the controller
• 3 level of password
• 3 sets of alternative configuration
• Direct communication with EFI engines
• Tier 4 final ready
• Remote monitoring and control
• Wide range of communication capabilities including:
  • connection via RS232, RS485, CAN and on board USB
  • internet access using Ethernet
  • Modbus (TCP/RTU)
• Active SMS and emails in different languages
• In-built PLC, complemented with a PLC monitoring tool in InteliConfig
• 6 binary inputs, 3 analog inputs and 6 binary outputs on-board
• 2 x high current binary outputs for cranking and fuel solenoid
• More I/Os available over plug-in or CAN modules (CM-BIO8-EFCP, Inteli AIN8, Inteli IO8/8, IGS-PTM)
• Remote Annunciator over CAN
• 1 slot for plug-in modules
• Real time clock
• Multipurpose flexible timers
• Flexible event based history with up to 350 events
• True RMS measurement
• Comprehensive protections
• UL Listed

• Interface between IG-PCM/PCLSM, InteliSys or Inteli NT controller and generator AVR

Power Supply Transformer for IG-AVRi Module ComAp - IG-AVRi-TRANS/LV

• Primary voltage 1: 230 - 277 VAC +- 20%
• Primary voltage 2: 400 - 480 VAC +- 20%
• Frequency range: 50 - 60 - 400 Hz

ECU Communication Bridge I-CB/MWM TEME

• Programmable interface unit between InteliGen NT, InteliSys NT or InteliDrive controllers and MWM (formelDeutz) TEM Evolution unit
• Configured analog and binary values, alarms and faults are received from MWM (Deutz) TEM Evolution unit via I-CB and displayed on IS measurement screens
• UART interface
• UL certified

Binary Inputs/Outputs and Analog Outputs Module - Inteli IO8/8

The extension module Inteli IO8/8 offers users more binary inputs and outputs for ComAp controllers. The unit offers the user the flexibility to configure the unit to have 8 binary inputs, 8 binary outputs, and 2 analog outputs, or 16 binary inputs, 0 binary outputs and 2 analog outputs via switches inside the controller. The Inteli IO8/8 is compatible with the InteliDrive DCU, InteliMains NT, InteliGen NT and InteliSys NT ranges of controllers.

Module is possible to configure (by switch on board) to two configurations:
 

1) Configuration 8/8

• 8 Binary inputs (options: pull up or pull down logic)
• 8 Binary outputs (options: Low side switch (LSS) or High side switch (HSS))
• 2 Analog outputs (options: voltage (0-10V), current (0-20mA) and PWM (5V, adjustable frequency 200Hz-2,4kHz))

2) Configuration 16/0

• 16 Binary inputs (options: pull up or pull down)
• 0 Binary outputs
• 2 Analog outputs (options: voltage (0-10V), current (0-20mA) and PWM (5V, adjustable frequency 200Hz-2,4kHz))

• Up to 12 Inteli IO8/8 module (in configuration 8/8) can be connected to the controller (InteliSys NT / InteliGen NT / InteliMains NT)
• Up to  6  Inteli IO8/8 module (in configuration 16/0) can be connected to the controller (InteliSys NT / InteliGen NT / InteliMains NT)
• Up to  4  Inteli IO8/8 (in configuration 8/8) can be connected to the InteliDrive DCU controller.
• LED indication of each Binary input/output
• Safety function of Binary output: Regular reading of the real state of the Binary output
• All settings are carried onboard switch or electronically (No jumpers)